Steel Detailing | Precast Detailing | Estimation

Author: admin

  • Design of Sheds

    Relevant Australian Standards

    AS/NZS 1170.0 General Principles

    AS/NSZ 1170.1 Permanent and Imposed Actions

    AS/NSZ 1170.2 Wind Actions

    AS NSZ 1170.4 Earth Quake Actions

    Member Design Standards

    AS/NZS 4600 Cold Formed Steel Structures

    AS 4100 : Steel Structures

    AS/NZS 5131 Fabrication and Erection of Structural Steelwork

    The Foundation Standards
    AS 2870 Residential Slabs and Footings

    AS 3600 Concrete Structures

    AS 2159 Piling Design and Installation

    Material Specifics

    AS/NSZ 3679.1 Hot Rolled bars and sections

    AS/NZS 1163 Cold formed structural steel hollow sections.

    AS/NSZ 1397 Steel sheet and strip

  • Minimum Pocket Depth for Coloumns

    Minimum Pocket Depth for Coloumns

    What is the minimum pocket depth required for rebated coloumns

    The minimum washer size is 3 mm. This could be different. If nothing is mentioned use 3 mm.

    The minimum bolt stick out should be 1 pitch. For M20 it is 2.5 mm. Use 10 mm stick out.

    Also there is grout. Pockets when cast could be of different depths. Use design grout of 15 mm minimum.

    The top of the bolt should be 35 mm below slab level to prevent concrete Cracking.

    Hence to be practical use 100 mm pocket depth with a base plate thickness of 16 mm and bolt size of 20 mm.

  • Foot Bridges | WalkWays | Pedestrian over passes

    • Foot Bridges | WalkWays | Pedestrian over passes

    • Warnambool Overpass | Steel Detailing

      Warrnambool Foot Bridge

  • Warrnambool Foot Bridge

    Warrnambool Foot Bridge

    Pedestrian overpass Foot Bridge steel drafting

    Trimble Connect Model
    Warrnambool Pedestrian Over pass Lift Structure

    Expert Steel Draftsman | Foot bridge | Pedestrian over pass | Walk Ways

    Street AddressWarnambool
    StateVictoria
    CountryAustralia
    ModelerGanesh | Ramakrishnan

  • Precast Blogs

    Precast Blogs

  • Mount Alvernia College

    Mount Alvernia College

    Trimble Connect Model
    Steel Esto,atopm
    Expert Take Off Service from Tek1

    Mount Alvernia College

    Expert MTO. Fast. Low Cost call us on.

    Expert Material Takeoff and Steel Estimation Services

    Competitve pricing

    Tel: 0425791837

  • Navigate a million Changes?

    Navigate a million Changes?

    Trimble Connect Model

    Meticulous Care – Expertise alone not sufficent

    Meticulous Care – Expertise alone not sufficent With many many changes, Mulitple site meaures, point cloud data, unless the processes are good and the care is meticulous, the knowledge and expertise will not count Street Address ATL Station State NSW Country Australia Modeler Ganesh Kumar

    When it comes to shop drawings and steel detailing, expertise, knowledge of software alone will not make it

    With many many changes, Mulitple site meaures, point cloud data, unless the processes are good and the care is meticulous, the knowledge and expertise will not count

    Street AddressATL Station
    StateNSW
    CountryAustralia
    ModelerGanesh Kumar

  • .Net | Python Ruby on Rails

    • What is an ObservableCollection?

      For those wanting a simple answer without the geek-speak, I’ll try to explain: Normal Collections Every now and then I go to NYC and my friend asks me to buy stuff for him. So I take a shopping list with me. The list has a lot of things on there like: Hugo Boss jacket Clive…

    • The difference between Synchronous and Asynchronous Execution

      Synchronous Execution My boss is a busy man. He tells me to write the code. I tell him: Fine. I get started and he’s watching me like a vulture, standing behind me, off my shoulder. I’m like “Dude, WTF: why don’t you go and do something while I finish this?” he’s like: “No, I”m waiting…

    • Getting a Selection Set

      This is a code block from my award winning BlockUtility static class.. But you would want to create the selectionFilter according to your own requirements – hence I have not used a static class for getting the selection filter. Apologies for the lack of readability in my code. The blog just kills the formatting. What…

    • Showing an Assembly in the Model via a Tekla Drawing (Part I) – Tekla Open API Plugin

      I’ve created another Tekla plug in. And I’m calling it using a macro. What does this plug in do? Here is a demo: Basically it display an assembly in the model, from a given assembly drawing. Does that make sense? Well if not let’s elaborate: The Problem: I’m sure you’ll be having similar issues. So…

    • Create accurate grid from converted PDF Files

      This  tool works with Autocad. Usually the architects grid is not accurate to the decimal point for detailing purposes. Most detailers redraw the grid more accurately. This API tool let you select text in autocad and draw the grid automatically. Usually a pdf file converted to autocad is sufficient.  

  • Batch Edit a Part in Tekla Structures

    Batch Edit a Part in Tekla Structures

    TeklaStructures has a batch editing utility for Assemblies.

    However, if we have to batch edit parts there is nothing.

    Expert Steel Detailers demand Utilities

    Our detailers have demanded that we develop a utility to do batch editing of parts.

    (more…)