Steel Detailing | Precast Detailing | Estimation

Author: admin

  • Design of Sheds

    Relevant Australian Standards

    AS/NZS 1170.0 General Principles

    AS/NSZ 1170.1 Permanent and Imposed Actions

    AS/NSZ 1170.2 Wind Actions

    AS NSZ 1170.4 Earth Quake Actions

    Member Design Standards

    AS/NZS 4600 Cold Formed Steel Structures

    AS 4100 : Steel Structures

    AS/NZS 5131 Fabrication and Erection of Structural Steelwork

    The Foundation Standards
    AS 2870 Residential Slabs and Footings

    AS 3600 Concrete Structures

    AS 2159 Piling Design and Installation

    Material Specifics

    AS/NSZ 3679.1 Hot Rolled bars and sections

    AS/NZS 1163 Cold formed structural steel hollow sections.

    AS/NSZ 1397 Steel sheet and strip

  • Minimum Pocket Depth for Coloumns

    Minimum Pocket Depth for Coloumns

    What is the minimum pocket depth required for rebated coloumns

    The minimum washer size is 3 mm. This could be different. If nothing is mentioned use 3 mm.

    The minimum bolt stick out should be 1 pitch. For M20 it is 2.5 mm. Use 10 mm stick out.

    Also there is grout. Pockets when cast could be of different depths. Use design grout of 15 mm minimum.

    The top of the bolt should be 35 mm below slab level to prevent concrete Cracking.

    Hence to be practical use 100 mm pocket depth with a base plate thickness of 16 mm and bolt size of 20 mm.

  • Foot Bridges | WalkWays | Pedestrian over passes

    • Foot Bridges | WalkWays | Pedestrian over passes

    • Warnambool Overpass | Steel Detailing

      Warrnambool Foot Bridge

  • Warrnambool Foot Bridge

    Warrnambool Foot Bridge

    Pedestrian overpass Foot Bridge steel drafting

    Trimble Connect Model
    Warrnambool Pedestrian Over pass Lift Structure

    Expert Steel Draftsman | Foot bridge | Pedestrian over pass | Walk Ways

    Street AddressWarnambool
    StateVictoria
    CountryAustralia
    ModelerGanesh | Ramakrishnan

  • Precast Blogs

    Precast Blogs

  • Mount Alvernia College

    Mount Alvernia College

    Trimble Connect Model
    Steel Esto,atopm
    Expert Take Off Service from Tek1

    Mount Alvernia College

    Expert MTO. Fast. Low Cost call us on.

    Expert Material Takeoff and Steel Estimation Services

    Competitve pricing

    Tel: 0425791837

  • Navigate a million Changes?

    Navigate a million Changes?

    Trimble Connect Model

    Meticulous Care – Expertise alone not sufficent

    Meticulous Care – Expertise alone not sufficent With many many changes, Mulitple site meaures, point cloud data, unless the processes are good and the care is meticulous, the knowledge and expertise will not count Street Address ATL Station State NSW Country Australia Modeler Ganesh Kumar

    When it comes to shop drawings and steel detailing, expertise, knowledge of software alone will not make it

    With many many changes, Mulitple site meaures, point cloud data, unless the processes are good and the care is meticulous, the knowledge and expertise will not count

    Street AddressATL Station
    StateNSW
    CountryAustralia
    ModelerGanesh Kumar

  • .Net | Python Ruby on Rails

    • Dont Lose time with missing dimensions

      Do you loose time with missing dimensions Have you ever used the wrong revision? Here is what is cooking at Tek1. If you would lik to to know more Here is a solution where you can scan the QR code and bring up the assembly model. know the revision number of the drawing which you…

    • Precast Panels with Tekla Structures

      This is probably first precast project we have attempted with tekla structures as the tool. We have done a few with Revit, and lot with Autocad. There is raging argument with no one really know (unless one has walked in the weeds) which is a better tool I believe no tool as out of the…

    • Why aren’t the user defined attributes being defined – in Tekla’s “Open” API

      If you want to waste time on a poorly documented API (which doesn’t make any sense) I would highly recommend getting on Tekla. I’m documenting this so some poor soul doesn’t waste a day trying to debug this: Do you see the problem? First insert the beam, and then apply the UDA and it should…

    • How to check if you have a legitimate Tekla Profile using the Tekla Open API

      Our use case? How can we check? Voila! Now it’s hard to make a mistake. If you want to get all materials – it’s very similar to the above. Use the CatalogHandler.GetMaterialItems() method along with the materialItem.MaterialName property. The code to actually do that – I will leave as an exercise to the reader.

    • How to Get Tekla Model Objects if selected by Users (Tekla API)

      A user has pre-selected a set of model objects. We need to retrieve them via the API. How do we do it? All of our code is extracted from our production apps.

  • Batch Edit a Part in Tekla Structures

    Batch Edit a Part in Tekla Structures

    TeklaStructures has a batch editing utility for Assemblies.

    However, if we have to batch edit parts there is nothing.

    Expert Steel Detailers demand Utilities

    Our detailers have demanded that we develop a utility to do batch editing of parts.

    (more…)