Author: admin
-
-
Design of Sheds
Relevant Australian Standards
AS/NZS 1170.0 General Principles
AS/NSZ 1170.1 Permanent and Imposed Actions
AS/NSZ 1170.2 Wind Actions
AS NSZ 1170.4 Earth Quake Actions
Member Design Standards
AS/NZS 4600 Cold Formed Steel Structures
AS 4100 : Steel Structures
AS/NZS 5131 Fabrication and Erection of Structural Steelwork
The Foundation Standards
AS 2870 Residential Slabs and FootingsAS 3600 Concrete Structures
AS 2159 Piling Design and Installation
Material Specifics
AS/NSZ 3679.1 Hot Rolled bars and sections
AS/NZS 1163 Cold formed structural steel hollow sections.
AS/NSZ 1397 Steel sheet and strip
-
Minimum Pocket Depth for Coloumns
What is the minimum pocket depth required for rebated coloumns
The minimum washer size is 3 mm. This could be different. If nothing is mentioned use 3 mm.
The minimum bolt stick out should be 1 pitch. For M20 it is 2.5 mm. Use 10 mm stick out.
Also there is grout. Pockets when cast could be of different depths. Use design grout of 15 mm minimum.
The top of the bolt should be 35 mm below slab level to prevent concrete Cracking.
Hence to be practical use 100 mm pocket depth with a base plate thickness of 16 mm and bolt size of 20 mm.
-
Foot Bridges | WalkWays | Pedestrian over passes
-
Foot Bridges | WalkWays | Pedestrian over passes
-
Warrnambool Foot Bridge
-
-
Warrnambool Foot Bridge
Pedestrian overpass Foot Bridge steel drafting
Expert Steel Draftsman | Foot bridge | Pedestrian over pass | Walk Ways
Street Address Warnambool State Victoria Country Australia Modeler Ganesh | Ramakrishnan -
Mount Alvernia College
Expert Take Off Service from Tek1 Mount Alvernia College
Expert MTO. Fast. Low Cost call us on.
Expert Material Takeoff and Steel Estimation Services
Competitve pricing
Tel: 0425791837
-
Navigate a million Changes?
Meticulous Care – Expertise alone not sufficent
Meticulous Care – Expertise alone not sufficent With many many changes, Mulitple site meaures, point cloud data, unless the processes are good and the care is meticulous, the knowledge and expertise will not count Street Address ATL Station State NSW Country Australia Modeler Ganesh Kumar
With many many changes, Mulitple site meaures, point cloud data, unless the processes are good and the care is meticulous, the knowledge and expertise will not count
Street Address ATL Station State NSW Country Australia Modeler Ganesh Kumar -
.Net | Python Ruby on Rails
-
Dont Lose time with missing dimensions
Do you loose time with missing dimensions Have you ever used the wrong revision? Here is what is cooking at Tek1. If you would lik to to know more Here is a solution where you can scan the QR code and bring up the assembly model. know the revision number of the drawing which you…
-
Precast Panels with Tekla Structures
This is probably first precast project we have attempted with tekla structures as the tool. We have done a few with Revit, and lot with Autocad. There is raging argument with no one really know (unless one has walked in the weeds) which is a better tool I believe no tool as out of the…
-
Why aren’t the user defined attributes being defined – in Tekla’s “Open” API
If you want to waste time on a poorly documented API (which doesn’t make any sense) I would highly recommend getting on Tekla. I’m documenting this so some poor soul doesn’t waste a day trying to debug this: Do you see the problem? First insert the beam, and then apply the UDA and it should…
-
How to check if you have a legitimate Tekla Profile using the Tekla Open API
Our use case? How can we check? Voila! Now it’s hard to make a mistake. If you want to get all materials – it’s very similar to the above. Use the CatalogHandler.GetMaterialItems() method along with the materialItem.MaterialName property. The code to actually do that – I will leave as an exercise to the reader.
-
How to Get Tekla Model Objects if selected by Users (Tekla API)
A user has pre-selected a set of model objects. We need to retrieve them via the API. How do we do it? All of our code is extracted from our production apps.
-
