Steel Detailing | Precast Detailing | Estimation

Author: admin

  • Design of Sheds

    Relevant Australian Standards

    AS/NZS 1170.0 General Principles

    AS/NSZ 1170.1 Permanent and Imposed Actions

    AS/NSZ 1170.2 Wind Actions

    AS NSZ 1170.4 Earth Quake Actions

    Member Design Standards

    AS/NZS 4600 Cold Formed Steel Structures

    AS 4100 : Steel Structures

    AS/NZS 5131 Fabrication and Erection of Structural Steelwork

    The Foundation Standards
    AS 2870 Residential Slabs and Footings

    AS 3600 Concrete Structures

    AS 2159 Piling Design and Installation

    Material Specifics

    AS/NSZ 3679.1 Hot Rolled bars and sections

    AS/NZS 1163 Cold formed structural steel hollow sections.

    AS/NSZ 1397 Steel sheet and strip

  • Minimum Pocket Depth for Coloumns

    Minimum Pocket Depth for Coloumns

    What is the minimum pocket depth required for rebated coloumns

    The minimum washer size is 3 mm. This could be different. If nothing is mentioned use 3 mm.

    The minimum bolt stick out should be 1 pitch. For M20 it is 2.5 mm. Use 10 mm stick out.

    Also there is grout. Pockets when cast could be of different depths. Use design grout of 15 mm minimum.

    The top of the bolt should be 35 mm below slab level to prevent concrete Cracking.

    Hence to be practical use 100 mm pocket depth with a base plate thickness of 16 mm and bolt size of 20 mm.

  • Foot Bridges | WalkWays | Pedestrian over passes

    • Foot Bridges | WalkWays | Pedestrian over passes

    • Warnambool Overpass | Steel Detailing

      Warrnambool Foot Bridge

  • Warrnambool Foot Bridge

    Warrnambool Foot Bridge

    Pedestrian overpass Foot Bridge steel drafting

    Trimble Connect Model
    Warrnambool Pedestrian Over pass Lift Structure

    Expert Steel Draftsman | Foot bridge | Pedestrian over pass | Walk Ways

    Street AddressWarnambool
    StateVictoria
    CountryAustralia
    ModelerGanesh | Ramakrishnan

  • Precast Blogs

    Precast Blogs

  • Mount Alvernia College

    Mount Alvernia College

    Trimble Connect Model
    Steel Esto,atopm
    Expert Take Off Service from Tek1

    Mount Alvernia College

    Expert MTO. Fast. Low Cost call us on.

    Expert Material Takeoff and Steel Estimation Services

    Competitve pricing

    Tel: 0425791837

  • Navigate a million Changes?

    Navigate a million Changes?

    Trimble Connect Model

    Meticulous Care – Expertise alone not sufficent

    Meticulous Care – Expertise alone not sufficent With many many changes, Mulitple site meaures, point cloud data, unless the processes are good and the care is meticulous, the knowledge and expertise will not count Street Address ATL Station State NSW Country Australia Modeler Ganesh Kumar

    When it comes to shop drawings and steel detailing, expertise, knowledge of software alone will not make it

    With many many changes, Mulitple site meaures, point cloud data, unless the processes are good and the care is meticulous, the knowledge and expertise will not count

    Street AddressATL Station
    StateNSW
    CountryAustralia
    ModelerGanesh Kumar

  • .Net | Python Ruby on Rails

    • LineDirectionJigger (AutoCAD .net API Jig code)

      Many times, over my career in using AutoCAD, I’ve had this requirement: given a particular input vector, I’ve wanted to a jig a line perpendicular to it, within my code. Accordingly, I have written a little class which I call the LineDirectionJigger: basically it restricts users to select one direction or another. For the sake…

    • Precast Efficiency Tool: Efficiently Create Elevation Drawings

      Demo: Command: Marking Plan To Elevation from Tek1 on Vimeo. What does this command do? It quickly and easily allows you to create elevation drawings given a certain marking plan view of a panel. You need to first: (i) select the applicable panel lines, then (ii) you need to select a view direction. The way…

    • Check for Fake dimensions in Autocad before using it as reference model

      It is important to check for fake dimensions before using it as reference model in Tekla Please watch this video

    • Tekla Model Sharing

      Tekla has got model sharing with latest releases. However, nothing like that exists in previous releases. Now with API plugin from Tek1 you can share member placements on earlier versions. There is no Lic fees to for model sharing to be paid to Tekla. You as the main modeller decide to farm out member placements…

    • TeklaInterop Minimum checks

      Friends, there is no substitute to reading the documentation. The most up to date version of this is located in our Team Drive – but here is a local copy nonetheless. AutoCAD-Tekla-Interop-Documentation Following minimum checks should be carried out for interop The member-schedule CSV file has the all the layer names in the cad files…

  • Batch Edit a Part in Tekla Structures

    Batch Edit a Part in Tekla Structures

    TeklaStructures has a batch editing utility for Assemblies.

    However, if we have to batch edit parts there is nothing.

    Expert Steel Detailers demand Utilities

    Our detailers have demanded that we develop a utility to do batch editing of parts.

    (more…)