Steel Detailing | Precast Detailing | Estimation

Author: admin

  • Design of Sheds

    Relevant Australian Standards

    AS/NZS 1170.0 General Principles

    AS/NSZ 1170.1 Permanent and Imposed Actions

    AS/NSZ 1170.2 Wind Actions

    AS NSZ 1170.4 Earth Quake Actions

    Member Design Standards

    AS/NZS 4600 Cold Formed Steel Structures

    AS 4100 : Steel Structures

    AS/NZS 5131 Fabrication and Erection of Structural Steelwork

    The Foundation Standards
    AS 2870 Residential Slabs and Footings

    AS 3600 Concrete Structures

    AS 2159 Piling Design and Installation

    Material Specifics

    AS/NSZ 3679.1 Hot Rolled bars and sections

    AS/NZS 1163 Cold formed structural steel hollow sections.

    AS/NSZ 1397 Steel sheet and strip

  • Minimum Pocket Depth for Coloumns

    Minimum Pocket Depth for Coloumns

    What is the minimum pocket depth required for rebated coloumns

    The minimum washer size is 3 mm. This could be different. If nothing is mentioned use 3 mm.

    The minimum bolt stick out should be 1 pitch. For M20 it is 2.5 mm. Use 10 mm stick out.

    Also there is grout. Pockets when cast could be of different depths. Use design grout of 15 mm minimum.

    The top of the bolt should be 35 mm below slab level to prevent concrete Cracking.

    Hence to be practical use 100 mm pocket depth with a base plate thickness of 16 mm and bolt size of 20 mm.

  • Foot Bridges | WalkWays | Pedestrian over passes

    • Foot Bridges | WalkWays | Pedestrian over passes

    • Warnambool Overpass | Steel Detailing

      Warrnambool Foot Bridge

  • Warrnambool Foot Bridge

    Warrnambool Foot Bridge

    Pedestrian overpass Foot Bridge steel drafting

    Trimble Connect Model
    Warrnambool Pedestrian Over pass Lift Structure

    Expert Steel Draftsman | Foot bridge | Pedestrian over pass | Walk Ways

    Street AddressWarnambool
    StateVictoria
    CountryAustralia
    ModelerGanesh | Ramakrishnan

  • Precast Blogs

    Precast Blogs

    • Chalet 1 – White Horse Village

      We are proud to showcase our contribution to Chalet 1 – White Horse Village, a unique and technically demanding project located in a mountainous region. This development presented several engineering and detailing challenges, and our team was honoured to be part of the solution — delivering precision, coordination, and innovation from start to finish. Technical…

    • PREFABRICATED CONCRETE ELEMENTS

      (Temporary Fixing Inserts for As-Cast Element Tolerances) INTRODUCTION: To ensure proper alignment and structural efficiency in the handling and installation of prefabricated concrete elements by placing temporary fixing inserts within the allowable as-cast dimensional tolerances as specified in Australian Standard AS 3850.2:2015. Inserts for the temporary attaching of prefabricated concrete elements shall be placed within…

    • STAGGERED FERRULES PLACEMENT ON PRECAST PANEL

      The design drawings for one of our Precast Project we were working on suggests ferrules must be placed staggered as noted below. The Problem: However, these casting components, such as ferrules cannot be placed on both sides of a precast panel with a thickness of less than 250mm. This mainly causes ferrules to clash along…

  • Mount Alvernia College

    Mount Alvernia College

    Trimble Connect Model
    Steel Esto,atopm
    Expert Take Off Service from Tek1

    Mount Alvernia College

    Expert MTO. Fast. Low Cost call us on.

    Expert Material Takeoff and Steel Estimation Services

    Competitve pricing

    Tel: 0425791837

  • Navigate a million Changes?

    Navigate a million Changes?

    Trimble Connect Model

    Meticulous Care – Expertise alone not sufficent

    Meticulous Care – Expertise alone not sufficent With many many changes, Mulitple site meaures, point cloud data, unless the processes are good and the care is meticulous, the knowledge and expertise will not count Street Address ATL Station State NSW Country Australia Modeler Ganesh Kumar

    When it comes to shop drawings and steel detailing, expertise, knowledge of software alone will not make it

    With many many changes, Mulitple site meaures, point cloud data, unless the processes are good and the care is meticulous, the knowledge and expertise will not count

    Street AddressATL Station
    StateNSW
    CountryAustralia
    ModelerGanesh Kumar

  • .Net | Python Ruby on Rails

    • Autocad Plug-in: Creating Order Forms Automatically

      Normally creating order forms are a nightmare. How does everyone else create order forms? I have no idea how people do it. They would have to manually count/iterate through every single block which exists in the model space and simultaneously note down the parts’ associated panel number(s). They could do it on their PC, or…

    • WPF Tunnelling – Explanation by analogy

      Tunnelling – What is it? And no, I’m not referring to how El Chapo escaped.   Refresher: what is bubbling? In the last post we talked about “bubbling”. It’s kinda like those instances where you get a parking fine. If you don’t deal with it then, you’ll get another fine. If you don’t deal with…

    • What is a routed event?

      What is a routed event? This is the answer that is typical on Stack Overflow sites and other such forums: A routed event is a type of event that can invoke handlers on multiple listeners in an element tree, rather than just on the object that raised the event. It seems – with all due…

    • What is an event?

      Assumed knowledge: Assume you know what a method is.   What is an event? Let’s keep it simple. An event is anything which “happens”. “Oh great! That helps a lot :’(  ,“ I hear you say. Examples are in order: The President comes to town. He could come at anytime. You don’t know when he…

    • What is a call-back function?

      Example by Parable and Analogy I have a secretary. At the end of the day, I ask her to: (i) take the firm’s outgoing mail and to drop it off at the post office, and in addition to that, after she has dropped the mail off, I ask her to do something else: (ii) whatever…