Author: admin
-
-
Design of Sheds
Relevant Australian Standards
AS/NZS 1170.0 General Principles
AS/NSZ 1170.1 Permanent and Imposed Actions
AS/NSZ 1170.2 Wind Actions
AS NSZ 1170.4 Earth Quake Actions
Member Design Standards
AS/NZS 4600 Cold Formed Steel Structures
AS 4100 : Steel Structures
AS/NZS 5131 Fabrication and Erection of Structural Steelwork
The Foundation Standards
AS 2870 Residential Slabs and FootingsAS 3600 Concrete Structures
AS 2159 Piling Design and Installation
Material Specifics
AS/NSZ 3679.1 Hot Rolled bars and sections
AS/NZS 1163 Cold formed structural steel hollow sections.
AS/NSZ 1397 Steel sheet and strip
-
Minimum Pocket Depth for Coloumns
What is the minimum pocket depth required for rebated coloumns
The minimum washer size is 3 mm. This could be different. If nothing is mentioned use 3 mm.
The minimum bolt stick out should be 1 pitch. For M20 it is 2.5 mm. Use 10 mm stick out.
Also there is grout. Pockets when cast could be of different depths. Use design grout of 15 mm minimum.
The top of the bolt should be 35 mm below slab level to prevent concrete Cracking.
Hence to be practical use 100 mm pocket depth with a base plate thickness of 16 mm and bolt size of 20 mm.
-
Foot Bridges | WalkWays | Pedestrian over passes
-
Foot Bridges | WalkWays | Pedestrian over passes
-
Warrnambool Foot Bridge
-
-
Warrnambool Foot Bridge
Pedestrian overpass Foot Bridge steel drafting
Expert Steel Draftsman | Foot bridge | Pedestrian over pass | Walk Ways
Street Address Warnambool State Victoria Country Australia Modeler Ganesh | Ramakrishnan -
Precast Blogs
-
Chalet 1 – White Horse Village
We are proud to showcase our contribution to Chalet 1 – White Horse Village, a unique and technically demanding project located in a mountainous region. This development presented several engineering and detailing challenges, and our team was honoured to be part of the solution — delivering precision, coordination, and innovation from start to finish. Technical…
-
PREFABRICATED CONCRETE ELEMENTS
(Temporary Fixing Inserts for As-Cast Element Tolerances) INTRODUCTION: To ensure proper alignment and structural efficiency in the handling and installation of prefabricated concrete elements by placing temporary fixing inserts within the allowable as-cast dimensional tolerances as specified in Australian Standard AS 3850.2:2015. Inserts for the temporary attaching of prefabricated concrete elements shall be placed within…
-
STAGGERED FERRULES PLACEMENT ON PRECAST PANEL
The design drawings for one of our Precast Project we were working on suggests ferrules must be placed staggered as noted below. The Problem: However, these casting components, such as ferrules cannot be placed on both sides of a precast panel with a thickness of less than 250mm. This mainly causes ferrules to clash along…
-
-
Mount Alvernia College
Expert Take Off Service from Tek1 Mount Alvernia College
Expert MTO. Fast. Low Cost call us on.
Expert Material Takeoff and Steel Estimation Services
Competitve pricing
Tel: 0425791837
-
Navigate a million Changes?
Meticulous Care – Expertise alone not sufficent
Meticulous Care – Expertise alone not sufficent With many many changes, Mulitple site meaures, point cloud data, unless the processes are good and the care is meticulous, the knowledge and expertise will not count Street Address ATL Station State NSW Country Australia Modeler Ganesh Kumar
With many many changes, Mulitple site meaures, point cloud data, unless the processes are good and the care is meticulous, the knowledge and expertise will not count
Street Address ATL Station State NSW Country Australia Modeler Ganesh Kumar -
.Net | Python Ruby on Rails
-
What is an ObservableCollection?
For those wanting a simple answer without the geek-speak, I’ll try to explain: Normal Collections Every now and then I go to NYC and my friend asks me to buy stuff for him. So I take a shopping list with me. The list has a lot of things on there like: Hugo Boss jacket Clive…
-
The difference between Synchronous and Asynchronous Execution
Synchronous Execution My boss is a busy man. He tells me to write the code. I tell him: Fine. I get started and he’s watching me like a vulture, standing behind me, off my shoulder. I’m like “Dude, WTF: why don’t you go and do something while I finish this?” he’s like: “No, I”m waiting…
-
Getting a Selection Set
This is a code block from my award winning BlockUtility static class.. But you would want to create the selectionFilter according to your own requirements – hence I have not used a static class for getting the selection filter. Apologies for the lack of readability in my code. The blog just kills the formatting. What…
-
Showing an Assembly in the Model via a Tekla Drawing (Part I) – Tekla Open API Plugin
I’ve created another Tekla plug in. And I’m calling it using a macro. What does this plug in do? Here is a demo: Basically it display an assembly in the model, from a given assembly drawing. Does that make sense? Well if not let’s elaborate: The Problem: I’m sure you’ll be having similar issues. So…
-
Create accurate grid from converted PDF Files
This tool works with Autocad. Usually the architects grid is not accurate to the decimal point for detailing purposes. Most detailers redraw the grid more accurately. This API tool let you select text in autocad and draw the grid automatically. Usually a pdf file converted to autocad is sufficient.
-
