Author: admin
-
-
Design of Sheds
Relevant Australian Standards
AS/NZS 1170.0 General Principles
AS/NSZ 1170.1 Permanent and Imposed Actions
AS/NSZ 1170.2 Wind Actions
AS NSZ 1170.4 Earth Quake Actions
Member Design Standards
AS/NZS 4600 Cold Formed Steel Structures
AS 4100 : Steel Structures
AS/NZS 5131 Fabrication and Erection of Structural Steelwork
The Foundation Standards
AS 2870 Residential Slabs and FootingsAS 3600 Concrete Structures
AS 2159 Piling Design and Installation
Material Specifics
AS/NSZ 3679.1 Hot Rolled bars and sections
AS/NZS 1163 Cold formed structural steel hollow sections.
AS/NSZ 1397 Steel sheet and strip
-
Minimum Pocket Depth for Coloumns
What is the minimum pocket depth required for rebated coloumns
The minimum washer size is 3 mm. This could be different. If nothing is mentioned use 3 mm.
The minimum bolt stick out should be 1 pitch. For M20 it is 2.5 mm. Use 10 mm stick out.
Also there is grout. Pockets when cast could be of different depths. Use design grout of 15 mm minimum.
The top of the bolt should be 35 mm below slab level to prevent concrete Cracking.
Hence to be practical use 100 mm pocket depth with a base plate thickness of 16 mm and bolt size of 20 mm.
-
Foot Bridges | WalkWays | Pedestrian over passes
-
Foot Bridges | WalkWays | Pedestrian over passes
-
Warrnambool Foot Bridge
-
-
Warrnambool Foot Bridge
Pedestrian overpass Foot Bridge steel drafting
Expert Steel Draftsman | Foot bridge | Pedestrian over pass | Walk Ways
Street Address Warnambool State Victoria Country Australia Modeler Ganesh | Ramakrishnan -
Precast Blogs
-
Chalet 1 – White Horse Village
We are proud to showcase our contribution to Chalet 1 – White Horse Village, a unique and technically demanding project located in a mountainous region. This development presented several engineering and detailing challenges, and our team was honoured to be part of the solution — delivering precision, coordination, and innovation from start to finish. Technical…
-
PREFABRICATED CONCRETE ELEMENTS
(Temporary Fixing Inserts for As-Cast Element Tolerances) INTRODUCTION: To ensure proper alignment and structural efficiency in the handling and installation of prefabricated concrete elements by placing temporary fixing inserts within the allowable as-cast dimensional tolerances as specified in Australian Standard AS 3850.2:2015. Inserts for the temporary attaching of prefabricated concrete elements shall be placed within…
-
STAGGERED FERRULES PLACEMENT ON PRECAST PANEL
The design drawings for one of our Precast Project we were working on suggests ferrules must be placed staggered as noted below. The Problem: However, these casting components, such as ferrules cannot be placed on both sides of a precast panel with a thickness of less than 250mm. This mainly causes ferrules to clash along…
-
-
Mount Alvernia College
Expert Take Off Service from Tek1 Mount Alvernia College
Expert MTO. Fast. Low Cost call us on.
Expert Material Takeoff and Steel Estimation Services
Competitve pricing
Tel: 0425791837
-
Navigate a million Changes?
Meticulous Care – Expertise alone not sufficent
Meticulous Care – Expertise alone not sufficent With many many changes, Mulitple site meaures, point cloud data, unless the processes are good and the care is meticulous, the knowledge and expertise will not count Street Address ATL Station State NSW Country Australia Modeler Ganesh Kumar
With many many changes, Mulitple site meaures, point cloud data, unless the processes are good and the care is meticulous, the knowledge and expertise will not count
Street Address ATL Station State NSW Country Australia Modeler Ganesh Kumar -
.Net | Python Ruby on Rails
-
Modelling Complex Contour Plates using the Tekla Open API
How to create custom Contour Plates using the Tekla Open API from Tek1 on Vimeo. Manually creating contour plates from CSV file inputs will likely be disastrous. You’ll inevitably make mistakes and things won’t fit on site: it will be an uphill battle. You can obviate these issues by using the Tekla Open API to…
-
A Beginners guide to APIs
Is programming knowledge necessary only for a Software developer? You will find an answer for this question in this blog. With automation ruling the world, it is important for every business to adopt it into their workflows to stay competitive.People may encounter lots of issues and errors in day to day work which may affect…
-
GRASSHOPPER- THE VISUAL PROGRAMMING LINK FOR TEKLA
Ever wondered how to automate the processes in modeling of steel structures, increase efficiency and accuracy. Grasshopper has got all the answers. Grasshopper is a visual programming interface like the Dynamo we saw in the previous blogs. It is built in within the 3D modeling software called Rhino. Tekla has released a link which enables…
-
.dwg based Take off with custom Plug ins
Tek1 has developed .dwg based plugins which talk to Tekla to carry out take-off efficiently Take off is completed in .dwg based Cad systems very similar to modeling in Tekla. For BIM model the model is converted to Tekla Reports can be taken either from .dwg system or Tekla. Right now reports are being taken…
-
IntelliCad based Tools to support Material Take-off
You don’t need to spend $30,000 p/a on Tekla licenses. You can estimate steel based on IntelliCad based software. Here’s some software I wrote to make this happen: How to Model Beams on Intellicad based software from Tek1 on Vimeo. Demo: Create beam and Create Beam Lines from Tek1 on Vimeo.
-
