Tek1 has successfully completed the commercial project for the reputed organisation in Australia.
Initially, the scope of work involved the main steel for the shed, which we have successfully completed. (Preston tram shed). Subsequently, the client assigned us an additional scope, which includes the handrails for the mezzanine level, as well as stair 1 and stair 2.
Stair 1Stair 2Mezzanine level handrail
We have successfully completed the handrail detailing without any errors, and the client is satisfied with the quality of our work.
Tek1 has successfully completed the commercial project for the reputed organisation in Australia.
The scope of work involves providing privacy screens and their supports. We have encountered challenges with the aluminum screen bends during the project.
Initially, we received instructions that each screen should have a bend in all four directions, which we modeled and sent for approval.
Screen with bend on 4 sides
However, the client later requested that we split the top and bottom of the screen and provide separate pieces to be welded to the main screen.
Screen section viewScreen end side
Our client expressed satisfaction with our work.
Screen supportPost for screen supportPost side view
Tek1 has successfully completed the industrial project for the reputed organisation in Australia.
This project does not have any structural design drawings. Instead, the client has provided sample design drawings. Therefore, we need to coordinate our structural design with the architect’s drawings.
Detailed by Ganesh & team
We need to provide structural support for an overhead crane. TEK1 has provided the correct beam profiles for the structural support, and the client is satisfied with our design and shop drawings.
Detailed by Ganesh & team
Our main objective is to deliver high-quality drawings without any errors. TEK1 has successfully achieved this goal.
Tek1 has successfully completed the project for the reputed organisation in Australia .
Lots of timber connections involved with steel in this project. TEK1 provided all the supporting members for timber.Client is happy with the connections that we have provided which is not in their design.
Tek1 has successfully completed the residential project for the reputed organisation in Australia .
Lots of timber connections involved with steel in this project. TEK1 provided all the supporting members for timber.Client is happy with the connections that we have provided which is not in their design.
Things to be checked, if we get a spigot connection for a column
When we have a spigot connection, at top of the column and a base plate connection at bottom of the column, first we must check the clearance provided for the movement of the column in the spigot to avoid any difficulties during erection.
If the clearance is not sufficient, we must address the issue to the client along with some proposals. In our condition the following Suggestions were provided. We can postfix the Chemsets at any one side of the column ends We can increase the clearance to enable sufficient erection clearance for the column.
In the below case, the design demands to pre-fix the chemset bolts and have provided only 50mm clearance for the spigot movement.
Refer below snaps from model & structural design.
In the above snap, the bottom of column has 10 thick base plate with Ø12 Chemset bolts and the top of the column is connected to the slab through the spigot which has 10 thick top plate with Ø12 chemset bolts as per the structural design requirement.
The structural engineer advised to pre-fix the chemset bolts.
So, we need to check for erection clearance to install the column.
The clearance between Soffit to the top of slab is 2940mm (Refer model snap). When we deduct the projection of the chemset at top 30mm (10mm top plate thick + 20mm projection) and at bottom 45mm (15mm grout + 10mm base plate thick + 20mm projection) from the slab to slab clearance (2940mm) we get 2865mm (2940-30-45=2865).
But the length of the column (when the spigot is fully inside the column and the top plate only projects out) is 2865 (column length) + 10 (Top plate of spigot) = 2875 mm which is 10mm more than that of the clearance between chemset projections.
So, considering this 10mm extra length and providing 15mm clearance at top and bottom, we have prepared a markup proposing 50mm (clearance as per design) + 40mm (10mm extra length of column + 15mm clearance on top & bottom) = 90mm spigot movement for easy erection and this proposal was sent to client.
Client had understood the issue and agreed our connection proposal with 90mm clearance.
Our analysis towards erection possibility along with client’s attention and understanding of the issue that we have addressed made the columns easy to erect.
TEK1 did a detailing for proposed residence project for reputed client in Australia.This project includes lot of timber beams. TEK1 will provide all the timber supports which connected to steel.
We did not miss any of the connections & finished this project without any error.
TEK1 recently did the 5-different types of railway Maintenance stairs with varying chainage. We are using our own macros to Model & detail these stairs pretty easier.
